KLUBER PRODUCTS

Klübersynth GH 6 oils
Synthetic gear and high temperature oils
Klübersynth GH 6-32, 46, 80, 100, 150, 220, 320, 460, 680, 1000 Edition 10.08, replaces edition 05.08
Article numbers: 012157/012009/012158/012159/012160/012161/012162/012163/012164/012165, 012281 en MA-TM/HSi
Benefits for your application
• The oils meet the requirements according to DIN 51 517 – 03, CLP. Corresponding gears
can be switched to Klübersynth GH 6 oils without prior consultation with the gear
manufacturer provided the general application notes are observed.
• As of ISO VG 220 the scuffing load stage API GL 5 is achieved. Gears are sufficiently
protected against scuffing even under high peak loads.
• Much longer service life than mineral oils due to the excellent ageing and oxidation
resistance of the base oil; thus maintenance intervals can be extended and in certain
cases even lifetime lubrication is possible
• Owing to the wide service temperature range a single viscosity grade can cover both low
and high temperatures in many applications
• The optimum friction behaviour of the polyglycol base oil reduces power losses and
improves efficiency
• The good wear protection of both gears and rolling bearings ensures that the service life
calculated for the lubricated components is achieved
• The excellent viscosity-temperature behaviour supports the formation of a sufficient
lubricating film even at elevated and high temperatures
• Seals made of 72 NBR 902, 75 FKM 585 and 75 FKM 170055 are resistant to Klübersynth
GH 6 oils. Leakage and contamination are prevented.
• Approved by Flender, SEW Eurodrive, Getriebebau Nord, Stöber Antriebstechnik, Lenze,
ZAE Antriebstechnik, Bonfiglioli, Rossi Motoriduttori, Motovario, Moventas, etc.
Description
Klübersynth GH 6 oils are gear oils on a
polyglycol basis. They have a high scuffing load
capacity and micro-pitting resistance.
These oils have also proved their good wear
protection in rolling bearings on the FAG FE 8
test rig for gear oils.
Klübersynth GH 6 oils stand out for their
excellent ageing and oxidation resistance, good
viscosity-temperature behaviour and very good
thermal stability.
Application
Klübersynth GH 6 oils were especially
developed for the lubrication of worm gears with
steel/bronze pairings.
The polyglycol base oils and special additives
reduce the friction coefficient and provide low
wear values, which is a clear advantage in
these applications.
Klübersynth GH 6 oils achieve a particularly low
wear intensity according to DIN 3996
(calculation of load capacity of worm gears).
Klübersynth GH 6 oils are also used for the
lubrication of bevel and spur gears, rolling and
plain bearings as well as all types of denture
couplings, especially when exposed to high
temperatures.
Klübersynth GH 6 oils can also be used for the
lubrication of lifting, drive and transport chains. Learn More

Klübersynth GH 6 oils
Synthetic gear and high temperature oils
Klübersynth GH 6-32, 46, 80, 100, 150, 220, 320, 460, 680, 1000 Edition 10.08, replaces edition 05.08
Article numbers: 012157/012009/012158/012159/012160/012161/012162/012163/012164/012165, 012281 en MA-TM/HSi
Benefits for your application
• The oils meet the requirements according to DIN 51 517 – 03, CLP. Corresponding gears
can be switched to Klübersynth GH 6 oils without prior consultation with the gear
manufacturer provided the general application notes are observed.
• As of ISO VG 220 the scuffing load stage API GL 5 is achieved. Gears are sufficiently
protected against scuffing even under high peak loads.
• Much longer service life than mineral oils due to the excellent ageing and oxidation
resistance of the base oil; thus maintenance intervals can be extended and in certain
cases even lifetime lubrication is possible
• Owing to the wide service temperature range a single viscosity grade can cover both low
and high temperatures in many applications
• The optimum friction behaviour of the polyglycol base oil reduces power losses and
improves efficiency
• The good wear protection of both gears and rolling bearings ensures that the service life
calculated for the lubricated components is achieved
• The excellent viscosity-temperature behaviour supports the formation of a sufficient
lubricating film even at elevated and high temperatures
• Seals made of 72 NBR 902, 75 FKM 585 and 75 FKM 170055 are resistant to Klübersynth
GH 6 oils. Leakage and contamination are prevented.
• Approved by Flender, SEW Eurodrive, Getriebebau Nord, Stöber Antriebstechnik, Lenze,
ZAE Antriebstechnik, Bonfiglioli, Rossi Motoriduttori, Motovario, Moventas, etc.
Description
Klübersynth GH 6 oils are gear oils on a
polyglycol basis. They have a high scuffing load
capacity and micro-pitting resistance.
These oils have also proved their good wear
protection in rolling bearings on the FAG FE 8
test rig for gear oils.
Klübersynth GH 6 oils stand out for their
excellent ageing and oxidation resistance, good
viscosity-temperature behaviour and very good
thermal stability.
Application
Klübersynth GH 6 oils were especially
developed for the lubrication of worm gears with
steel/bronze pairings.
The polyglycol base oils and special additives
reduce the friction coefficient and provide low
wear values, which is a clear advantage in
these applications.
Klübersynth GH 6 oils achieve a particularly low
wear intensity according to DIN 3996
(calculation of load capacity of worm gears).
Klübersynth GH 6 oils are also used for the
lubrication of bevel and spur gears, rolling and
plain bearings as well as all types of denture
couplings, especially when exposed to high
temperatures.
Klübersynth GH 6 oils can also be used for the
lubrication of lifting, drive and transport chains. Learn More

Klübersynth GH 6 oils
Synthetic gear and high temperature oils
Klübersynth GH 6-32, 46, 80, 100, 150, 220, 320, 460, 680, 1000 Edition 10.08, replaces edition 05.08
Article numbers: 012157/012009/012158/012159/012160/012161/012162/012163/012164/012165, 012281 en MA-TM/HSi
Benefits for your application
• The oils meet the requirements according to DIN 51 517 – 03, CLP. Corresponding gears
can be switched to Klübersynth GH 6 oils without prior consultation with the gear
manufacturer provided the general application notes are observed.
• As of ISO VG 220 the scuffing load stage API GL 5 is achieved. Gears are sufficiently
protected against scuffing even under high peak loads.
• Much longer service life than mineral oils due to the excellent ageing and oxidation
resistance of the base oil; thus maintenance intervals can be extended and in certain
cases even lifetime lubrication is possible
• Owing to the wide service temperature range a single viscosity grade can cover both low
and high temperatures in many applications
• The optimum friction behaviour of the polyglycol base oil reduces power losses and
improves efficiency
• The good wear protection of both gears and rolling bearings ensures that the service life
calculated for the lubricated components is achieved
• The excellent viscosity-temperature behaviour supports the formation of a sufficient
lubricating film even at elevated and high temperatures
• Seals made of 72 NBR 902, 75 FKM 585 and 75 FKM 170055 are resistant to Klübersynth
GH 6 oils. Leakage and contamination are prevented.
• Approved by Flender, SEW Eurodrive, Getriebebau Nord, Stöber Antriebstechnik, Lenze,
ZAE Antriebstechnik, Bonfiglioli, Rossi Motoriduttori, Motovario, Moventas, etc.
Description
Klübersynth GH 6 oils are gear oils on a
polyglycol basis. They have a high scuffing load
capacity and micro-pitting resistance.
These oils have also proved their good wear
protection in rolling bearings on the FAG FE 8
test rig for gear oils.
Klübersynth GH 6 oils stand out for their
excellent ageing and oxidation resistance, good
viscosity-temperature behaviour and very good
thermal stability.
Application
Klübersynth GH 6 oils were especially
developed for the lubrication of worm gears with
steel/bronze pairings.
The polyglycol base oils and special additives
reduce the friction coefficient and provide low
wear values, which is a clear advantage in
these applications.
Klübersynth GH 6 oils achieve a particularly low
wear intensity according to DIN 3996
(calculation of load capacity of worm gears).
Klübersynth GH 6 oils are also used for the
lubrication of bevel and spur gears, rolling and
plain bearings as well as all types of denture
couplings, especially when exposed to high
temperatures.
Klübersynth GH 6 oils can also be used for the
lubrication of lifting, drive and transport chains. Learn More

Klübersynth GH 6 oils
Synthetic gear and high temperature oils
Klübersynth GH 6-32, 46, 80, 100, 150, 220, 320, 460, 680, 1000 Edition 10.08, replaces edition 05.08
Article numbers: 012157/012009/012158/012159/012160/012161/012162/012163/012164/012165, 012281 en MA-TM/HSi
Benefits for your application
• The oils meet the requirements according to DIN 51 517 – 03, CLP. Corresponding gears
can be switched to Klübersynth GH 6 oils without prior consultation with the gear
manufacturer provided the general application notes are observed.
• As of ISO VG 220 the scuffing load stage API GL 5 is achieved. Gears are sufficiently
protected against scuffing even under high peak loads.
• Much longer service life than mineral oils due to the excellent ageing and oxidation
resistance of the base oil; thus maintenance intervals can be extended and in certain
cases even lifetime lubrication is possible
• Owing to the wide service temperature range a single viscosity grade can cover both low
and high temperatures in many applications
• The optimum friction behaviour of the polyglycol base oil reduces power losses and
improves efficiency
• The good wear protection of both gears and rolling bearings ensures that the service life
calculated for the lubricated components is achieved
• The excellent viscosity-temperature behaviour supports the formation of a sufficient
lubricating film even at elevated and high temperatures
• Seals made of 72 NBR 902, 75 FKM 585 and 75 FKM 170055 are resistant to Klübersynth
GH 6 oils. Leakage and contamination are prevented.
• Approved by Flender, SEW Eurodrive, Getriebebau Nord, Stöber Antriebstechnik, Lenze,
ZAE Antriebstechnik, Bonfiglioli, Rossi Motoriduttori, Motovario, Moventas, etc.
Description
Klübersynth GH 6 oils are gear oils on a
polyglycol basis. They have a high scuffing load
capacity and micro-pitting resistance.
These oils have also proved their good wear
protection in rolling bearings on the FAG FE 8
test rig for gear oils.
Klübersynth GH 6 oils stand out for their
excellent ageing and oxidation resistance, good
viscosity-temperature behaviour and very good
thermal stability.
Application
Klübersynth GH 6 oils were especially
developed for the lubrication of worm gears with
steel/bronze pairings.
The polyglycol base oils and special additives
reduce the friction coefficient and provide low
wear values, which is a clear advantage in
these applications.
Klübersynth GH 6 oils achieve a particularly low
wear intensity according to DIN 3996
(calculation of load capacity of worm gears).
Klübersynth GH 6 oils are also used for the
lubrication of bevel and spur gears, rolling and
plain bearings as well as all types of denture
couplings, especially when exposed to high
temperatures.
Klübersynth GH 6 oils can also be used for the
lubrication of lifting, drive and transport chains. Learn More

<Klübersynth GH 6 oils
Synthetic gear and high temperature oils
Klübersynth GH 6-32, 46, 80, 100, 150, 220, 320, 460, 680, 1000 Edition 10.08, replaces edition 05.08
Article numbers: 012157/012009/012158/012159/012160/012161/012162/012163/012164/012165, 012281 en MA-TM/HSi
Benefits for your application
• The oils meet the requirements according to DIN 51 517 – 03, CLP. Corresponding gears
can be switched to Klübersynth GH 6 oils without prior consultation with the gear
manufacturer provided the general application notes are observed.
• As of ISO VG 220 the scuffing load stage API GL 5 is achieved. Gears are sufficiently
protected against scuffing even under high peak loads.
• Much longer service life than mineral oils due to the excellent ageing and oxidation
resistance of the base oil; thus maintenance intervals can be extended and in certain
cases even lifetime lubrication is possible
• Owing to the wide service temperature range a single viscosity grade can cover both low
and high temperatures in many applications
• The optimum friction behaviour of the polyglycol base oil reduces power losses and
improves efficiency
• The good wear protection of both gears and rolling bearings ensures that the service life
calculated for the lubricated components is achieved
• The excellent viscosity-temperature behaviour supports the formation of a sufficient
lubricating film even at elevated and high temperatures
• Seals made of 72 NBR 902, 75 FKM 585 and 75 FKM 170055 are resistant to Klübersynth
GH 6 oils. Leakage and contamination are prevented.
• Approved by Flender, SEW Eurodrive, Getriebebau Nord, Stöber Antriebstechnik, Lenze,
ZAE Antriebstechnik, Bonfiglioli, Rossi Motoriduttori, Motovario, Moventas, etc.
Description
Klübersynth GH 6 oils are gear oils on a
polyglycol basis. They have a high scuffing load
capacity and micro-pitting resistance.
These oils have also proved their good wear
protection in rolling bearings on the FAG FE 8
test rig for gear oils.
Klübersynth GH 6 oils stand out for their
excellent ageing and oxidation resistance, good
viscosity-temperature behaviour and very good
thermal stability.
Application
Klübersynth GH 6 oils were especially
developed for the lubrication of worm gears with
steel/bronze pairings.
The polyglycol base oils and special additives
reduce the friction coefficient and provide low
wear values, which is a clear advantage in
these applications.
Klübersynth GH 6 oils achieve a particularly low
wear intensity according to DIN 3996
(calculation of load capacity of worm gears).
Klübersynth GH 6 oils are also used for the
lubrication of bevel and spur gears, rolling and
plain bearings as well as all types of denture
couplings, especially when exposed to high
temperatures.
Klübersynth GH 6 oils can also be used for the
lubrication of lifting, drive and transport chains. Learn More

Klübersynth GH 6 oils
Synthetic gear and high temperature oils
Klübersynth GH 6-32, 46, 80, 100, 150, 220, 320, 460, 680, 1000 Edition 10.08, replaces edition 05.08
Article numbers: 012157/012009/012158/012159/012160/012161/012162/012163/012164/012165, 012281 en MA-TM/HSi
Benefits for your application
• The oils meet the requirements according to DIN 51 517 – 03, CLP. Corresponding gears
can be switched to Klübersynth GH 6 oils without prior consultation with the gear
manufacturer provided the general application notes are observed.
• As of ISO VG 220 the scuffing load stage API GL 5 is achieved. Gears are sufficiently
protected against scuffing even under high peak loads.
• Much longer service life than mineral oils due to the excellent ageing and oxidation
resistance of the base oil; thus maintenance intervals can be extended and in certain
cases even lifetime lubrication is possible
• Owing to the wide service temperature range a single viscosity grade can cover both low
and high temperatures in many applications
• The optimum friction behaviour of the polyglycol base oil reduces power losses and
improves efficiency
• The good wear protection of both gears and rolling bearings ensures that the service life
calculated for the lubricated components is achieved
• The excellent viscosity-temperature behaviour supports the formation of a sufficient
lubricating film even at elevated and high temperatures
• Seals made of 72 NBR 902, 75 FKM 585 and 75 FKM 170055 are resistant to Klübersynth
GH 6 oils. Leakage and contamination are prevented.
• Approved by Flender, SEW Eurodrive, Getriebebau Nord, Stöber Antriebstechnik, Lenze,
ZAE Antriebstechnik, Bonfiglioli, Rossi Motoriduttori, Motovario, Moventas, etc.
Description
Klübersynth GH 6 oils are gear oils on a
polyglycol basis. They have a high scuffing load
capacity and micro-pitting resistance.
These oils have also proved their good wear
protection in rolling bearings on the FAG FE 8
test rig for gear oils.
Klübersynth GH 6 oils stand out for their
excellent ageing and oxidation resistance, good
viscosity-temperature behaviour and very good
thermal stability.
Application
Klübersynth GH 6 oils were especially
developed for the lubrication of worm gears with
steel/bronze pairings.
The polyglycol base oils and special additives
reduce the friction coefficient and provide low
wear values, which is a clear advantage in
these applications.
Klübersynth GH 6 oils achieve a particularly low
wear intensity according to DIN 3996
(calculation of load capacity of worm gears).
Klübersynth GH 6 oils are also used for the
lubrication of bevel and spur gears, rolling and
plain bearings as well as all types of denture
couplings, especially when exposed to high
temperatures.
Klübersynth GH 6 oils can also be used for the
lubrication of lifting, drive and transport chains. Learn More

Klübersynth GH 6 oils
Synthetic gear and high temperature oils
Klübersynth GH 6-32, 46, 80, 100, 150, 220, 320, 460, 680, 1000 Edition 10.08, replaces edition 05.08
Article numbers: 012157/012009/012158/012159/012160/012161/012162/012163/012164/012165, 012281 en MA-TM/HSi
Benefits for your application
• The oils meet the requirements according to DIN 51 517 – 03, CLP. Corresponding gears
can be switched to Klübersynth GH 6 oils without prior consultation with the gear
manufacturer provided the general application notes are observed.
• As of ISO VG 220 the scuffing load stage API GL 5 is achieved. Gears are sufficiently
protected against scuffing even under high peak loads.
• Much longer service life than mineral oils due to the excellent ageing and oxidation
resistance of the base oil; thus maintenance intervals can be extended and in certain
cases even lifetime lubrication is possible
• Owing to the wide service temperature range a single viscosity grade can cover both low
and high temperatures in many applications
• The optimum friction behaviour of the polyglycol base oil reduces power losses and
improves efficiency
• The good wear protection of both gears and rolling bearings ensures that the service life
calculated for the lubricated components is achieved
• The excellent viscosity-temperature behaviour supports the formation of a sufficient
lubricating film even at elevated and high temperatures
• Seals made of 72 NBR 902, 75 FKM 585 and 75 FKM 170055 are resistant to Klübersynth
GH 6 oils. Leakage and contamination are prevented.
• Approved by Flender, SEW Eurodrive, Getriebebau Nord, Stöber Antriebstechnik, Lenze,
ZAE Antriebstechnik, Bonfiglioli, Rossi Motoriduttori, Motovario, Moventas, etc.
Description
Klübersynth GH 6 oils are gear oils on a
polyglycol basis. They have a high scuffing load
capacity and micro-pitting resistance.
These oils have also proved their good wear
protection in rolling bearings on the FAG FE 8
test rig for gear oils.
Klübersynth GH 6 oils stand out for their
excellent ageing and oxidation resistance, good
viscosity-temperature behaviour and very good
thermal stability.
Application
Klübersynth GH 6 oils were especially
developed for the lubrication of worm gears with
steel/bronze pairings.
The polyglycol base oils and special additives
reduce the friction coefficient and provide low
wear values, which is a clear advantage in
these applications.
Klübersynth GH 6 oils achieve a particularly low
wear intensity according to DIN 3996
(calculation of load capacity of worm gears).
Klübersynth GH 6 oils are also used for the
lubrication of bevel and spur gears, rolling and
plain bearings as well as all types of denture
couplings, especially when exposed to high
temperatures.
Klübersynth GH 6 oils can also be used for the
lubrication of lifting, drive and transport chains. Learn More

Klübersynth GH 6 oils
Synthetic gear and high temperature oils
Klübersynth GH 6-32, 46, 80, 100, 150, 220, 320, 460, 680, 1000 Edition 10.08, replaces edition 05.08
Article numbers: 012157/012009/012158/012159/012160/012161/012162/012163/012164/012165, 012281 en MA-TM/HSi
Benefits for your application
• The oils meet the requirements according to DIN 51 517 – 03, CLP. Corresponding gears
can be switched to Klübersynth GH 6 oils without prior consultation with the gear
manufacturer provided the general application notes are observed.
• As of ISO VG 220 the scuffing load stage API GL 5 is achieved. Gears are sufficiently
protected against scuffing even under high peak loads.
• Much longer service life than mineral oils due to the excellent ageing and oxidation
resistance of the base oil; thus maintenance intervals can be extended and in certain
cases even lifetime lubrication is possible
• Owing to the wide service temperature range a single viscosity grade can cover both low
and high temperatures in many applications
• The optimum friction behaviour of the polyglycol base oil reduces power losses and
improves efficiency
• The good wear protection of both gears and rolling bearings ensures that the service life
calculated for the lubricated components is achieved
• The excellent viscosity-temperature behaviour supports the formation of a sufficient
lubricating film even at elevated and high temperatures
• Seals made of 72 NBR 902, 75 FKM 585 and 75 FKM 170055 are resistant to Klübersynth
GH 6 oils. Leakage and contamination are prevented.
• Approved by Flender, SEW Eurodrive, Getriebebau Nord, Stöber Antriebstechnik, Lenze,
ZAE Antriebstechnik, Bonfiglioli, Rossi Motoriduttori, Motovario, Moventas, etc.
Description
Klübersynth GH 6 oils are gear oils on a
polyglycol basis. They have a high scuffing load
capacity and micro-pitting resistance.
These oils have also proved their good wear
protection in rolling bearings on the FAG FE 8
test rig for gear oils.
Klübersynth GH 6 oils stand out for their
excellent ageing and oxidation resistance, good
viscosity-temperature behaviour and very good
thermal stability.
Application
Klübersynth GH 6 oils were especially
developed for the lubrication of worm gears with
steel/bronze pairings.
The polyglycol base oils and special additives
reduce the friction coefficient and provide low
wear values, which is a clear advantage in
these applications.
Klübersynth GH 6 oils achieve a particularly low
wear intensity according to DIN 3996
(calculation of load capacity of worm gears).
Klübersynth GH 6 oils are also used for the
lubrication of bevel and spur gears, rolling and
plain bearings as well as all types of denture
couplings, especially when exposed to high
temperatures.
Klübersynth GH 6 oils can also be used for the
lubrication of lifting, drive and transport chains. Learn More

Learn More

Learn More

Learn More

Learn More

Klübersynth ® UH1 14-1600
Synthetic lubricating grease for the food and pharmaceutical
processing industry.

Benefits for your application
— NSF H1 registered supporting process reliability
— Good wear protection with FZG test scuffing load stage 11
— Component life enhanced resulting from a special thickener with good adhesion and
corrosion protection
— Good pumpability in centralised systems
Application
Klübersynth UH1 14-1600 is especially suitable
for applications in machines and installations
used in the food processing and pharmaceutical
industries where contact with the food product
is technically unavoidable.
It is intended for use as a fluid gear grease for
the immersion lubrication of toothed gears,
worm gears and chains operating more
smoothly with a softer grease.
Description
Klübersynth UH1 14-1600 is a high performance
lubricating grease especially
developed for the food processing and
pharmaceutical industries.
It is registered as NSF H1 and complies with
FDA 21 CFR Sec. 178.3570. Furthermore the
product has been designed in the light of the
requirements of the ISO 21469 / DIN V 10517.
With its soft consistency Klübersynth UH1 14-
1600 is particularly suitable as a fluid gear
grease providing good antiwear protection. It
also ensures good protection against corrosion
and is mineral hydrocarbon free.
Application notes
Klübersynth UH1 14-1600 can be applied by
brush, spatula, grease gun, or grease cartridge.
It can also be dispensed through centralised
single-line lubrication systems.
Before substituting Klübersynth UH1 14-1600
for other greases, thoroughly clean the
lubrication/friction points. If the greases are
miscible, relubrication is sufficient. In gears,
however, used grease should be removed as
far as possible. Learn More

High-temperature lubricating greases
STABUTHERM GH 461, STABUTHERM GH 462, article number: 020500, 020511, en Edition 04.09, replaces edition 01.08
MA-SP/SP
Benefits for your application
— Reduction of lubricant costs due to lower consumption
— Reduced waste water disposal costs due to excellent water resistance
— Considerable reduction of bearing costs due to good wear protection, good load- carrying
capacity and excellent corrosion protection
— Trouble-free operation of machines due to good pumpability and metering in central
lubrication systems**
— Low wear at high temperatures.

STABUTHERM GH 462 are high-temperature
lubricating greases based on mineral oil and
polyurea. They have a wide service
temperature range and can be applied in rolling
bearings up to 180°C.
STABUTHERM GH 462 are suitable for
applications in smelting works and rolling mills,
especially for high-temperature lubrication
points supplied through a central lubrication
system, e.g.
- drive rollers in continuous casting
installations (slabs and billets)
- conveyor rollers in continuous furnaces.
Lubricants for such applications must meet
extremely high requirements regarding
operating temperature, scaling, water and
ensuing corrosion.
STABUTHERM GH 461 and
STABUTHERM GH 462 are also suitable for
other high-temperature applications, such as:
- annealing furnaces, drying stoves
- plain bearings in foundry cranes
- hot rolls in cardboard manufacturing
plants
- road tarmacking machines
- shut-off gates in bulk material
installations
- cooling beds, conveyor systems
- rotary kilns
- machines and installations in the
automotive, beverage, glass and
ceramics industries
Application notes
STABUTHERM GH 461 and STABUTHERM
GH 462 can be pumped through all common
types of lubrication systems**.
Pipe friction values were determined in order to
assess the pumpability in central lubrication
systems. Learn More

High-temperature lubricating greases
STABUTHERM GH 461, STABUTHERM GH 462, article number: 020500, 020511, en Edition 04.09, replaces edition 01.08
MA-SP/SP
Benefits for your application
— Reduction of lubricant costs due to lower consumption
— Reduced waste water disposal costs due to excellent water resistance
— Considerable reduction of bearing costs due to good wear protection, good load- carrying
capacity and excellent corrosion protection
— Trouble-free operation of machines due to good pumpability and metering in central
lubrication systems**
— Low wear at high temperatures.

STABUTHERM GH 462 are high-temperature
lubricating greases based on mineral oil and
polyurea. They have a wide service
temperature range and can be applied in rolling
bearings up to 180°C.
STABUTHERM GH 462 are suitable for
applications in smelting works and rolling mills,
especially for high-temperature lubrication
points supplied through a central lubrication
system, e.g.
- drive rollers in continuous casting
installations (slabs and billets)
- conveyor rollers in continuous furnaces.
Lubricants for such applications must meet
extremely high requirements regarding
operating temperature, scaling, water and
ensuing corrosion.
STABUTHERM GH 461 and
STABUTHERM GH 462 are also suitable for
other high-temperature applications, such as:
- annealing furnaces, drying stoves
- plain bearings in foundry cranes
- hot rolls in cardboard manufacturing
plants
- road tarmacking machines
- shut-off gates in bulk material
installations
- cooling beds, conveyor systems
- rotary kilns
- machines and installations in the
automotive, beverage, glass and
ceramics industries
Application notes
STABUTHERM GH 461 and STABUTHERM
GH 462 can be pumped through all common
types of lubrication systems**.
Pipe friction values were determined in order to
assess the pumpability in central lubrication
systems. Learn More

Klübersynth GH 6 oils
Synthetic gear and high temperature oils
Klübersynth GH 6-32, 46, 80, 100, 150, 220, 320, 460, 680, 1000 Edition 10.08, replaces edition 05.08
Article numbers: 012157/012009/012158/012159/012160/012161/012162/012163/012164/012165, 012281 en MA-TM/HSi
Benefits for your application
• The oils meet the requirements according to DIN 51 517 – 03, CLP. Corresponding gears
can be switched to Klübersynth GH 6 oils without prior consultation with the gear
manufacturer provided the general application notes are observed.
• As of ISO VG 220 the scuffing load stage API GL 5 is achieved. Gears are sufficiently
protected against scuffing even under high peak loads.
• Much longer service life than mineral oils due to the excellent ageing and oxidation
resistance of the base oil; thus maintenance intervals can be extended and in certain
cases even lifetime lubrication is possible
• Owing to the wide service temperature range a single viscosity grade can cover both low
and high temperatures in many applications
• The optimum friction behaviour of the polyglycol base oil reduces power losses and
improves efficiency
• The good wear protection of both gears and rolling bearings ensures that the service life
calculated for the lubricated components is achieved
• The excellent viscosity-temperature behaviour supports the formation of a sufficient
lubricating film even at elevated and high temperatures
• Seals made of 72 NBR 902, 75 FKM 585 and 75 FKM 170055 are resistant to Klübersynth
GH 6 oils. Leakage and contamination are prevented.
• Approved by Flender, SEW Eurodrive, Getriebebau Nord, Stöber Antriebstechnik, Lenze,
ZAE Antriebstechnik, Bonfiglioli, Rossi Motoriduttori, Motovario, Moventas, etc.
Description
Klübersynth GH 6 oils are gear oils on a
polyglycol basis. They have a high scuffing load
capacity and micro-pitting resistance.
These oils have also proved their good wear
protection in rolling bearings on the FAG FE 8
test rig for gear oils.
Klübersynth GH 6 oils stand out for their
excellent ageing and oxidation resistance, good
viscosity-temperature behaviour and very good
thermal stability.
Application
Klübersynth GH 6 oils were especially
developed for the lubrication of worm gears with
steel/bronze pairings.
The polyglycol base oils and special additives
reduce the friction coefficient and provide low
wear values, which is a clear advantage in
these applications.
Klübersynth GH 6 oils achieve a particularly low
wear intensity according to DIN 3996
(calculation of load capacity of worm gears).
Klübersynth GH 6 oils are also used for the
lubrication of bevel and spur gears, rolling and
plain bearings as well as all types of denture
couplings, especially when exposed to high
temperatures.
Klübersynth GH 6 oils can also be used for the
lubrication of lifting, drive and transport chains. Learn More

Klüberquiet® BQH 72-102
High-purity rolling bearing grease for long-term lubrication
Klüberquiet BQH 72-102, Art. No.: 094023, en Edition 08.07, replaces edition 05.07
GATE-B/SP
Benefits for your application
— Cost savings due to long service life of grease at > 80°C
— Smooth running, low noise
— Wide service temperature range allows a variety of applications
— Long bearing life due to excellent water resistance
Description
Klüberquiet BQH 72-102 is a synthetic hightemperature
lubricating grease. Due to the
careful selection of product components and
the clean manufacturing environment,
Klüberquiet BQH 72-102 is a rolling bearing
grease with a particularly low noise level.
Klüberquiet BQH 72-102 offers excellent
performance characteristics thanks to a highquality
ester oil, a new polyurea thickener and
special additives. It is special in that it combines
high-temperature resistance and extreme
purity.
Application
In a wide variety of ball bearings operating
under extreme thermal stress, Klüberquiet BQH
72-102 is used for long-term or lifetime
lubrication. Such applications include:
- Ball bearings in electric motors, fans, air
conditioners, generators and belt tensioners
in cars, power tool as well as household
appliances and office equipment. Learn More

ISOFLEX NCA 15 is a dynamically
light grease with good pressure
absorption properties for plain and
rolling bearings. It consists of ester
oil, synthetic hydrocarbon oil,
mineral oil and special calcium
soap. The product is resistant to
water and protects reliably against
wear.
Application:
ISOFLEX NCA 15 is particularly
suitable for the lubrication of spindle
and tapered roller bearings,
threaded spindles, ball screws
subject to high loads, and for all
high-speed bearings, e.g. bearings
in OE-spinning turbines used in the
textile industry. It is also suitable for
tooth flanks of precision gears
(bevel gears in milling machines).
Application notes:
The lubricant is applied by brush,
spatula, grease gun or grease
cartridge. Owing to the different
compositions of elastomers and
plastic materials, compatibility tests
are indispensable before series
application.


• Rolling bearing grease
• For very high speeds
• Good pressure absorption
• Good resistance to water
• Good wear protection
• Resistant to oxidation and
ageing
Product data:
Colour beige
Texture homogeneous,
short-fibred
Density, at 20 °C, g/cm3, approx. 0.94
Service temperature range*, °C, approx. – 50 to 120
Drop point, DIN ISO 2176, °C > 180
Worked penetration, DIN ISO 2137,
(ASTM D 217); 0.1 mm 265 to 295
Water resistance, DIN 51 807/1,
3 h / 90 °c, rating 0/1 – 90
Base oil viscosity, DIN 51 562/1,
at 40 °C, mm2/s, approx.
at 100 °C, mm2/s, approx.
23.0
4.7
Speed factor**
(n x dm), mm x min–1, approx. 1,300,000
Apparent dynamic viscosity***,
Klüber viscosity grade L/M Learn More

ISOFLEX NCA 15 is a dynamically
light grease with good pressure
absorption properties for plain and
rolling bearings. It consists of ester
oil, synthetic hydrocarbon oil,
mineral oil and special calcium
soap. The product is resistant to
water and protects reliably against
wear.
Application:
ISOFLEX NCA 15 is particularly
suitable for the lubrication of spindle
and tapered roller bearings,
threaded spindles, ball screws
subject to high loads, and for all
high-speed bearings, e.g. bearings
in OE-spinning turbines used in the
textile industry. It is also suitable for
tooth flanks of precision gears
(bevel gears in milling machines).
Application notes:
The lubricant is applied by brush,
spatula, grease gun or grease
cartridge. Owing to the different
compositions of elastomers and
plastic materials, compatibility tests
are indispensable before series
application. Learn More

ISOFLEX NCA 15 is a dynamically
light grease with good pressure
absorption properties for plain and
rolling bearings. It consists of ester
oil, synthetic hydrocarbon oil,
mineral oil and special calcium
soap. The product is resistant to
water and protects reliably against
wear.
Application:
ISOFLEX NCA 15 is particularly
suitable for the lubrication of spindle
and tapered roller bearings,
threaded spindles, ball screws
subject to high loads, and for all
high-speed bearings, e.g. bearings
in OE-spinning turbines used in the
textile industry. It is also suitable for
tooth flanks of precision gears
(bevel gears in milling machines).
Application notes:
The lubricant is applied by brush,
spatula, grease gun or grease
cartridge. Owing to the different
compositions of elastomers and
plastic materials, compatibility tests
are indispensable before series
application. Learn More

ISOFLEX NCA 15 is a dynamically
light grease with good pressure
absorption properties for plain and
rolling bearings. It consists of ester
oil, synthetic hydrocarbon oil,
mineral oil and special calcium
soap. The product is resistant to
water and protects reliably against
wear.
Application:
ISOFLEX NCA 15 is particularly
suitable for the lubrication of spindle
and tapered roller bearings,
threaded spindles, ball screws
subject to high loads, and for all
high-speed bearings, e.g. bearings
in OE-spinning turbines used in the
textile industry. It is also suitable for
tooth flanks of precision gears
(bevel gears in milling machines).
Application notes:
The lubricant is applied by brush,
spatula, grease gun or grease
cartridge. Owing to the different
compositions of elastomers and
plastic materials, compatibility tests
are indispensable before series
application. Learn More

ISOFLEX NCA 15 is a dynamically
light grease with good pressure
absorption properties for plain and
rolling bearings. It consists of ester
oil, synthetic hydrocarbon oil,
mineral oil and special calcium
soap. The product is resistant to
water and protects reliably against
wear.
Application:
ISOFLEX NCA 15 is particularly
suitable for the lubrication of spindle
and tapered roller bearings,
threaded spindles, ball screws
subject to high loads, and for all
high-speed bearings, e.g. bearings
in OE-spinning turbines used in the
textile industry. It is also suitable for
tooth flanks of precision gears
(bevel gears in milling machines).
Application notes:
The lubricant is applied by brush,
spatula, grease gun or grease
cartridge. Owing to the different
compositions of elastomers and
plastic materials, compatibility tests
are indispensable before series
application. Learn More

Klübersynth G 34-130 is a
lubricating grease based on
synthetic hydrocarbon oil, mineral
oil, special Ca soap and polyurea. It
has a wide service temperature
range, good antiwear properties and
high resistance to ageing.
Klübersynth G 34-130 provides
excellent protection against
tribocorrosion resistance to water
and good adhesion.
Application
For gears, bearings, joints and
slideways, for example in machines
for craftsmen and do-it-yourselfers.
Generally suitable for small and
miniature gears with steel/steel,
steel/plastic and plastic/plastic
friction components.
Klübersynth G 34-130 is particularly
suitable for slideways with
aluminium sliding components and
for the lubrication of trapezoidal or
ball-type threaded spindles.
Application notes
Immersion lubrication of gears up to
a peripheral speed of approx. 5 m/s
and for tooth flank greasing up to
approx. 4 m/s.
The product is applied by brush,
spatula or automatic metering
devices*. Learn More

Klübersynth G 34-130 is a
lubricating grease based on
synthetic hydrocarbon oil, mineral
oil, special Ca soap and polyurea. It
has a wide service temperature
range, good antiwear properties and
high resistance to ageing.
Klübersynth G 34-130 provides
excellent protection against
tribocorrosion resistance to water
and good adhesion.
Application
For gears, bearings, joints and
slideways, for example in machines
for craftsmen and do-it-yourselfers.
Generally suitable for small and
miniature gears with steel/steel,
steel/plastic and plastic/plastic
friction components.
Klübersynth G 34-130 is particularly
suitable for slideways with
aluminium sliding components and
for the lubrication of trapezoidal or
ball-type threaded spindles.
Application notes
Immersion lubrication of gears up to
a peripheral speed of approx. 5 m/s
and for tooth flank greasing up to
approx. 4 m/s.
The product is applied by brush,
spatula or automatic metering
devices* Learn More

Klübersynth UH1 14-151 was especially
developed for the food processing and
pharmaceutical industry.
This lubricant has been registered by the
NSF for use in federally inspected meat and
poultry plants (NSF H1) and complies with FDA
21 CFR § 178.3570.
Klübersynth UH1 14-151 shows good anti-wear
properties, water resistance and corrosion
protection as well as a high ageing and
oxidation stability.
Klübersynth UH1 14-151 is speciality grease
based on synthetic hydrocarbon oil and an
aluminium complex soap.
Application
Used for machines and equipment
in the food processing and pharmaceutical
industry, particularly for lubrication points that
may have incidental and technically
unavoidable contact with the food product.
However, we recommend using Klübersynth
UH1 14-151 at all lubrication points, in order to
avoid problems due to lubricant contamination.
This special grease lubricates rolling and sliding
bearings, lifting cylinders, joints, guide bars,
cams, etc. Learn More

Klübersynth UH1 14-151 was especially
developed for the food processing and
pharmaceutical industry.
This lubricant has been registered by the
NSF for use in federally inspected meat and
poultry plants (NSF H1) and complies with FDA
21 CFR § 178.3570.
Klübersynth UH1 14-151 shows good anti-wear
properties, water resistance and corrosion
protection as well as a high ageing and
oxidation stability.
Klübersynth UH1 14-151 is speciality grease
based on synthetic hydrocarbon oil and an
aluminium complex soap.
Application
Used for machines and equipment
in the food processing and pharmaceutical
industry, particularly for lubrication points that
may have incidental and technically
unavoidable contact with the food product.
However, we recommend using Klübersynth
UH1 14-151 at all lubrication points, in order to
avoid problems due to lubricant contamination.
This special grease lubricates rolling and sliding
bearings, lifting cylinders, joints, guide bars,
cams, etc. Learn More